![[PukiWiki]](image/pukiwiki.png "[PukiWiki]")
「.NET 開発基盤部会 Wiki」は、「Open棟梁Project」,「OSSコンソーシアム .NET開発基盤部会」によって運営されています。
Linuxを触りたかったので、SHIRASAGIハンズオンの開発環境準備をしてみた。
SHIRASAGIハンズオンの開発環境は、Vagrant + VirtualBox?で準備する。
私はWin 10 proを用意しました。
An error occurred while downloading the remote file. The error message, if any, is reproduced below. Please fix this error and try again.
※ SHIRASAGI開発環境として、動作確認のとれた vagrant バージョンをインストールする。
Tera Term などの SSH クライアントが必要。
Vagrantによる環境設定
Vagrantfile は Ruby の簡単な変数代入で書かれている。
公式にも「Rubyの知識は必要ない」と書いてある。
c:\shirasagi-dev\Vagrantfile
Vagrant.configure(2) do |config|
config.vm.box = "ss-vagrant-v1.6.0-rc"
config.vm.box_url = "https://github.com/shirasagi/ss-vagrant/releases/download/v1.6.0-rc/ss-vagrant-virtualbox-x86_64.box"
config.vm.network :forwarded_port, guest: 3000, host: 3000
config.vm.network "private_network", ip: "192.168.33.10"
config.vm.network "private_network", ip: "192.168.33.11"
config.vm.network "private_network", ip: "192.168.33.12"
config.vm.provider :virtualbox do |vb|
# see: http://blog.shibayu36.org/entry/2013/08/12/090545
# IPv6 と DNS でのネットワーク遅延対策で追記
vb.customize ["modifyvm", :id, "--natdnsproxy1", "off"]
vb.customize ["modifyvm", :id, "--natdnshostresolver1", "off"]
end
end>vagrant up
Bringing machine 'default' up with 'virtualbox' provider...
==> default: Box 'ss-vagrant-v1.6.0-rc' could not be found. Attempting to find and install...
default: Box Provider: virtualbox
default: Box Version: >= 0
==> default: Box file was not detected as metadata. Adding it directly...
==> default: Adding box 'ss-vagrant-v1.6.0-rc' (v0) for provider: virtualbox
default: Downloading: https://github.com/shirasagi/ss-vagrant/releases/download/v1.6.0-rc/ss-vagrant-virtualbox-x86_64.box
default: Progress: nn% (Rate: nnnnk/s, Estimated time remaining: n:nn:nn)==> default: Successfully added box 'ss-vagrant-v1.6.0-rc' (v0) for 'virtualbox'!
==> default: Importing base box 'ss-vagrant-v1.6.0-rc'...
==> default: Matching MAC address for NAT networking...
==> default: Setting the name of the VM: shirasagi-dev_default_1506394717167_57655
==> default: Clearing any previously set network interfaces...
==> default: Preparing network interfaces based on configuration...
default: Adapter 1: nat
default: Adapter 2: hostonly
default: Adapter 3: hostonly
default: Adapter 4: hostonly
==> default: Forwarding ports...
default: 3000 (guest) => 3000 (host) (adapter 1)
default: 22 (guest) => 2222 (host) (adapter 1)
==> default: Running 'pre-boot' VM customizations...
==> default: Booting VM...
==> default: Waiting for machine to boot. This may take a few minutes...
default: SSH address: 127.0.0.1:2222
default: SSH username: vagrant
default: SSH auth method: private keyTimed out while waiting for the machine to boot. This means that
Vagrant was unable to communicate with the guest machine within
the configured ("config.vm.boot_timeout" value) time period.
If you look above, you should be able to see the error(s) that
Vagrant had when attempting to connect to the machine. These errors
are usually good hints as to what may be wrong.
If you're using a custom box, make sure that networking is properly
working and you're able to connect to the machine. It is a common
problem that networking isn't setup properly in these boxes.
Verify that authentication configurations are also setup properly,
as well.
If the box appears to be booting properly, you may want to increase
the timeout ("config.vm.boot_timeout") value.vb.gui = true
>vagrant up
>vagrant up Bringing machine 'default' up with 'virtualbox' provider... >vagrant up Bringing machine 'default' up with 'virtualbox' provider... ==> default: Machine already provisioned. Run `vagrant provision` or use the `--provision` ==> default: flag to force provisioning. Provisioners marked to run always will still run.
[ディスプレイ] ---> [リモートディスプレイ] ---> [サーバーを有効化]のチェックをオフ
これで起動した？
Tera Termで接続
ググると色々出てくる。
